Flashing Lights In Eyes When I Blink

Samsung TV wont turn on blinking red light explained fix 18

I had a problem with my Flat screen TV notturning on. Instead of sending it in for repairs I decided to fix it. Using time lapse to speedthings up, I'll show you how I did it. First I disconnected and removed the TV from thewall and laid it face down on a flat carpeted floor. I then removed the rear panel screwsand lifted off the panel to get closer to accessing the boards inside. I wanted to geta closer look at the power supply board, as I suspected it was causing the problem. SoI disconnected more connectors, removed more Philips screws and then removed the metalprotective panel over the boards to gain access. Once the panel was off, I had a clear viewof the power supply board. It was the board

with the heavy power cable wires that wentto the wall outlet plug connector. Then I proceeded to carefully unplug the board. Ialso zeroed the high voltage capacitors that were present on the board. These on mine read450 volts. I did this by holding the plastic handle of the screwdriver and shorted thelegs of each capacitor together with the screwdriver blade to zero them. I then lifted the boardoff the chassis and took a closer look. I could clearly see that the tops of 2 electrolyticcapacitors were swollen. One was actually leaking. I decided to replace those, as wellas the 2 capacitors that were beside them. From my local electronics store, I purchased4 replacement capacitors. See my notes below

for details. All 4 items cost me a total of3 dollars. Using some Soder wick, a 25 watt soldering Iron, and some solder I proceededto remove and replace the 4 capacitors. After marking the bottom of the circuit board, Igently and carefully desoldered the capacitors. You can see that I clearly marked the polaritiesof the old capacitors on the circuit board. I took this information from the top of theboard by looking at the labels on the existing blown capacitors. One must always use theexact same voltage and capacity components when replacing parts on their devices. I hadno way of knowing whether the 2nd pair of capacitors were defective by visual inspection,but for the price, it was hard to go wrong

in replacing them. Once the old capacitorswere removed, I had to clean up the leftover solder residue from the board using soderwick. If this old residue was not removed, I would later have a tough time getting thenew ones in where the old ones came out. Now it's time to install the new electrolyticcapacitors. I'm careful to pay close attention to the polarity labeling of the new ones asI put them in. Careful not to get solder on any other components I progressively moveup the circuit board one connection at a time, always careful not to spend too much timein one spot. Excessive heat for extended periods on any connection can cause collateral damageto the components being soldered, the board,

or anything nearby. Once the connections wereall made, I carefully snipped off the long legs of the capacitors, and took a quick lookat the board afterwards. That's it. I reassembled the TV in the reverse order that I took itapart and fired it up. This repair I did 2 weeks ago, and as you can see, all is in order.Thanks for watching! And don't forget, I have many more tutorials for you, so please subscribe.

American Standard Blinking Red Light

I am having an American Standard furnace blinkingred light issue. I don't understand what it means. Don't worry, the blinking light codes arenot to hard to figure out. You need to watch it and pay close attention. Whyé Don't all the blinks mean the same thingé No, not at all. Your furnace is trying totalk to you through the LED light. What is it saying to meé First, you need to determine if it is continuouslyblinking, or if it is blinking some, then

stopping, then blinking again. Is it constant,or done in setsé It is just flashing over and over again. If it is pulsing on and off slowly it meansthat everything is just fine. Your unit is just sitting dormant, waiting for instructions. If it is blinking quickly, it means that yourAmerican Standard furnace is heating up and getting ready to warm your house. No worriesthere either. Don't freak out over the flashing light, eventhe owners manual states this is completely normal.

What if it is just constantly on, and doesn'tgo offé If it is lit up as a solid light, there issomething wrong with it. You shouldn't be seeing that. Now that you have me curious, what if my AmericanStandard furnace blinking red light was done in sets of flashes instead of a steady paceé That is when you know it is giving you diagnosticerror codes. You need to count the flashes to find out which one is the issue. Wow, you make it all so simple. It was gettingso complicated in my mind. I was about to

call in a repairman for no reason. You savedme a lot of money! No worries. I am glad I was able to calm yourfears.

Leave a Reply